March 2006
Special
eccentric press in
two track execution ready for the delivery and final assembly at in Hungary.
This is a press for the production of standard parts of the door- and
window-maker industries with lengths of up to 6100 mm. |
| 
|
| |
March 2006
Precautionary retrofit of the
feed control at a Soenen press in Italy. With this reorganization all
machines of these customer were switched over to Brück control. |
| 
|
|
February 2006
Retrofit of a Soenen perforating
press with several NC-axe for Infeed table, ram and wedge. Also the feed system
was replaced and switched over to standard components due to the age and
problems at the after-availability of spare parts. |
| 
|
| |
December 2005
Mechanical and electric full
modernization of a 35 years old Brück perforating press in the USA. |
| 
|
| |
December 2005
Precautionary reorganization of
a feed control system at a Soenen press in England. |
| 
|
| |
October 2005
Single-track Special
eccentric press with
safety light curtains and pressing force-measuring facilities for a customer in
Austria.
Parts, which are mainly established here, are for mounting units. |
| 
|
| |
October 2005
Delivery of an expanded metal
machine inside Germany. |
| 
|
| |
September 2005
Retrofit
of the feed control system of a Soenen machine in Italy after a complete failure. By
use of standard components this could go back in production after only 14 days. |
| 
|
| |
September 2005
Final
assembly of a 400t perforating press with a work width of 1600mm. Delivery
and final purchase with the customer in Spain in November. |
| 
|
| |
|
February 2005
500 t perforating press with active hold-down for an American customer in final assembly. This press is especially designed for punching thick metal sheets (1/4"/ 6.35mm).The press was officially accepted by the customer at the end of February 2005. |
|
 |
| |
|
December 2004
Official acceptance of expanded metal processing plant (40t expanded metal press and 160t flat roller) by British customer in Düren. |
|
 |
|
|
November 2004
Finally assembly and test running of a 250t perforating press for an American customer. This press is equipped with a completely novel stroke adjustment (automatic from control panel). This makes it suitable for both the processing of thinner sheets with shorter stroke cycles (max. 500min-1) and for thicker sheets. |
|
 |
|
|
October 2004
Official acceptance of an expanded metal press (24t) by a Spanish customer. The press is specially designed for producing fine meshes and operates with a stroke rate of 1000strokes/min. It was possible to again reduce the final price through a complete revision of the design. |
|
 |
|
|
September 2004
Expanded metal press (60t) ready for handover to the Spanish customer. |
|
 |
|
|
September 2004
Special plant for cropping and cutting wire to length for German producer of metal fabric completed and handed over to the customer ready for service. |
|
 |
|
|
July2004
500t perforating press with infeed table and travelling part shearing device in final assembly. Official acceptance by Spanish customer at Brück. Final assembly at customer's factory. |
|
 |
|
|
May 2004
630t long part press for production of window fittings for customer in Austria completed and tested. Twin track plant with 2 rams, 3 connecting rods per ram and tool adjusting device for setting the tools. |
|
 |
|
|
March 2004
Two column 400t press for German customer completed and delivered to customer. Table size: 800x3000mm, stroke rate max. 180min-1. |
|
 |
|
|
March 2004
Two column 300t press for German customer completed and delivered to customer. Table size: 1000x3000mm, stroke rate max. 32min-1, stroke travel 120mm. |
|
 |
|
top